MICROCRE · RESEARCH SCIENCE
钢铁与焊接结构
研究目标
围绕热处理、焊接区域和加工表面,连接组织、尺寸、局部硬度与宏观力学;以位置和状态对应防止不同材料层级混比。
研究问题
母材、热影响区和焊缝的组织变化是否与硬度及断裂位置对应?
几何偏差来自加工、热变形还是装夹与温度测量条件?
不同方向、表面和加载模式的结果是否真正可比?
组织与性能的关系
晶粒、相分布和热历史共同影响局部响应;需要显微证据与独立力学结果配对。
孔隙、夹杂及表面缺陷可能改变疲劳或冲击表现,平均硬度无法完整描述这些影响。
尺寸、粗糙度和残余状态影响装配与服役;测量报告需保留基准及空间尺度。
适用边界
硬度与强度换算必须有材料及状态适用依据。
实验室局部结果不能单独构成构件服役安全或寿命结论。
关联仪器、方法与研究依据
孔系尺寸与同轴基准链 →基准平面:平面度、直线度与支撑 →微结构尺度:晶粒、相与孔隙 →轴类零件:直径、圆度与圆柱形貌 →表面粗糙度:方向、滤波与功能联系 →压缩性能:端面、摩擦与失稳检查 →环境耐久:暴露条件、前后对照与外推限制 →疲劳研究:应力比、循环与未断样 →冲击性能:缺口、温度与吸收能量 →硬度与压入:标尺、尺度和接触模型 →拉伸性能:从尺寸到应力—应变与断口 →
论文关联表示方法或研究对象相关,不表示论文采用了本型号仪器。
Orientation imaging microscopy: application to the measurement of grain boundary structure →Orientation imaging: The emergence of a new microscopy →The impact of magnesium content on lithium-magnesium alloy electrode performance with argyrodite solid electrolyte →Ultraviolet digital image correlation (UV-DIC) for high temperature applications →Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques →Certification of Standard Reference Material® 2261a: Chlorinated Pesticides in Hexane (Nominal Mass Concentration 2 µg/mL) →Scaling approach to conical indentation in elastic-plastic solids with work hardening →Using nanoindentation to study the aging of cellulose acetate in cinematographic films →Computational modeling of the forward and reverse problems in instrumented sharp indentation →A procedure for extracting primary and secondary creep parameters from nanoindentation data →Size-affected single-slip behavior of pure nickel microcrystals →A method for interpreting the data from depth-sensing indentation instruments →Temperature dependence of the indentation size effect →The Measurement and Uncertainty of a Calibration Standard for the Scanning Electron Microscope →Distance-dependent influences on angle metrology with autocollimators in deflectometry →Environmental influences on autocollimator-based angle and form metrology →Self-calibration strategies for reducing systematic slope measurement errors of autocollimators in deflectometric profilometry →A novel approach for extending autocollimator calibration from plane to spatial angles →Size dependence of mechanical properties of gold at the micron scale in the absence of strain gradients →Infrared Optical Properties of Materials →Anisotropy oxidation behavior and mechanism of textured Ti3(SiAl)C2 ceramic →A simple method for high-precision calibration of an angle encoder using an electronic nulling autocollimator →Evaluation of measurement data — Guide to the expression of uncertainty in measurement →Evaluation of measurement data — Guide to the expression of uncertainty in measurement. Amendment 1: Nonlinearity in measurement models →Evaluation of measurement data — Supplement 1 to the GUM — Propagation of distributions using a Monte Carlo method →Guide to the expression of uncertainty in measurement — Part 6: Developing and using measurement models →Transmission EBSD from 10 nm domains in a scanning electron microscope →Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results →Indentation size effects in crystalline materials: A law for strain gradient plasticity →An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments →Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review →On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation →Traceability Calibration, & Measurement Uncertainty Issues Regarding Coordinate Measuring Machines and Other Complex Instruments →Discrepancies between roughness measurements obtained with phase-shifting and white-light interferometry →Fiji: an open-source platform for biological-image analysis →NIH Image to ImageJ: 25 years of image analysis →Surface characterization of an ultra-soft contact lens material using an atomic force microscopy nanoindentation method →Comparison of Bulk and Micro Sampling Techniques for the Elemental Analysis of SRM 610 and 612 →High-Temperature Mechanical Characterization of CeO2 as a Ceramic Surrogate Fuel Based on FIB and Nanoindentation →AFM z-piezo calibration method for height measurements in the sub-nanometer to nanometer range using stepped surfaces →Uncertainties in Small-Angle Measurement Systems Used to Calibrate Angle Artifacts →Determination of displacements using an improved digital correlation method →Hot nanoindentation in inert environments →Sample dimensions influence strength and crystal plasticity →Certification of Standard Reference Material® 2246a Relative Intensity Correction Standard for Raman Spectroscopy: 830 nm Excitation →NIST Surface Roughness and Step Height Calibrations: Measurement Conditions and Sources of Uncertainty →Measurement of high temperature full-field strain up to 2000 °C using digital image correlation →Mechanical Metallurgy on Columbia Gas X100 Experimental Pipe →High-resolution elastic strain measurement from electron backscatter diffraction patterns: new levels of sensitivity →A systematic study of sample preparation-induced martensitic phase formation in 304 L austenitic stainless steel →ASTM Technical Committee Guidance — DIC 测量的报告要求 →EURAMET Calibration Guide — 硬度计校准与不确定度评定 →NPL Good Practice Guide — DIC 散斑制备与质量评价 →NPL Good Practice Guide — 不确定度预算的编制 →Digital image correlation using Newton-Raphson method of partial differential correction →Applications of digital-image-correlation techniques to experimental mechanics →Scanning Electron Microscopy and X-ray Microanalysis →Evaluation of measurement data — Guide to the expression of uncertainty in measurement (GUM) →Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review — Extended reading 31 →Digital imaging techniques in experimental stress analysis →Image Correlation for Shape, Motion and Deformation Measurements →
