SHANGHAI MICROCRE OPTICS-MECH TECH CO., LTDAbout MICROCRE400-812-7833
MICROCRE · RESEARCH SCIENCE

Hardness and indentation: scale and contact models

Translation pending review.

Research track

performance

Research objective

Connect preparation, scale, force and impression validity while distinguishing conventional and instrumented hardness.

Objective

产生具有标尺、载荷与有效性证据的局部力学结果。

Required inputs

  • 材料厚度和组织尺度

  • 目标标尺及载荷范围

  • 参考块和压头状态

Workflow steps

  1. 01
    Title

    选择适用标尺

    Action

    依据材料、厚度和结构尺度选择方法,明确传统压痕尺寸或残余深度定义;各标尺之间不能无验证通用换算。

    Input

    材料及目标

    Output

    方法和尺度计划

    Quality gate

    方法范围与样品条件匹配

    If the check fails

    更换适用标尺或调整取样

  2. 02
    Title

    准备表面和支承

    Action

    逐级去除制样变形并保证支承稳定,检查曲率、粗糙度和背面影响;薄层样品须评估基体作用。

    Input

    样品及制样计划

    Output

    有效表面与安装

    Quality gate

    压痕尺寸相对表面和厚度合理

    If the check fails

    重复制样或改变测量尺度

    Instruments for this step
  3. 03
    Title

    核查参考与读数链

    Action

    用适用参考块检查力循环和测量系统,确认压头与图像标定;视觉自动识别仍需人工核对边界。

    Input

    参考块与配置

    Output

    核查和校准记录

    Quality gate

    所选标尺范围内核查有效

    If the check fails

    停止样品测量并校准

    Instruments for this step
  4. 04
    Title

    布点并按程序加载

    Action

    按组织位置安排间距和边缘距离,保留力及保持时间;重复压痕不能彼此影响,也不能只测最均匀区域。

    Input

    布点图与有效配置

    Output

    压痕位置及原始读数

    Quality gate

    点位与循环满足方法要求

    If the check fails

    重设布点或换区域后测试

    Instruments for this step
  5. 05
    Title

    判断压痕有效性

    Action

    检查轮廓、裂纹、端点和对角线差异,区分真实组织不均匀与读取错误;无效点须有图像依据。

    Input

    压痕图及数据

    Output

    有效性标签

    Quality gate

    剔除规则统一且保留原图

    If the check fails

    重新读数或另做有效压痕

    Instruments for this step
  6. 06
    Title

    计算与检查尺度效应

    Action

    使用正确力单位及标尺公式,按位置和载荷分组;载荷变化导致的结果差异需分析,不用简单平均掩盖。

    Input

    有效读数及单位

    Output

    硬度分布和误差预算

    Quality gate

    单位系数和条件完整

    If the check fails

    复算或增加载荷依赖验证

  7. 07
    Title

    报告并关联其他性能

    Action

    给出标尺、力、时间、位置和离散性。硬度反映局部响应,强度、韧性或耐磨推断需独立适用证据。

    Input

    审核结果

    Output

    局部硬度资料包

    Quality gate

    没有将硬度直接等同综合性能

    If the check fails

    增加对应性能试验

Equations and variables

  • Item

    维氏硬度的N制表达

    Equation

    HV≈0.1891F/d²

    Variables and units

    F为N,d为两对角线平均mm;结果为HV硬度数。

    Assumptions and limits

    有效维氏压痕及适用方法条件;系数为近似单位表达。

    Worked example

    F=9.80665 N,d=0.100 mm,HV≈185.44375。

Worked example

Assumed teaching inputs · not customer measurements

Input parameters

假设力9.80665 N、平均对角线0.100 mm。

Calculation

0.1891×9.80665/0.100²=185.4437515。

Result

维氏硬度数约185.44 HV。

Limitations

假设教学数据,不是客户实测或论文复现。不是MPa,也不代表所有载荷条件相同。

Numerical results
  • Item

    Vickers

    Value

    185.4437515

    Unit

    HV

Deliverables

  • 参考块和表面核查

  • 点位及原始压痕图

  • 条件化硬度分布

Errors and risks

  • N/kgf系数混用

  • 读取或制样误差

  • 尺度效应被平均掩盖

Instrument applicability

分类关联只表示研究链中的候选角色;具体型号、量程、附件、校准和方法适用性须逐项核对,不表示所引论文使用过本公司仪器。

Literature scope

文献链接提供相关方法、误差或材料机制背景。流程为本网站独立整理,不声称复现全部论文条件,也不声称论文使用本公司仪器。

Instrument roles in the workflow

Instrument familyRole and applicabilityWorkflow steps

用于本流程的相关步骤:核查参考与读数链、布点并按程序加载、判断压痕有效性

核查参考与读数链 · 布点并按程序加载 · 判断压痕有效性

用于本流程的相关步骤:核查参考与读数链、布点并按程序加载、判断压痕有效性

核查参考与读数链 · 布点并按程序加载 · 判断压痕有效性

用于本流程的相关步骤:核查参考与读数链

核查参考与读数链

用于本流程的相关步骤:核查参考与读数链

核查参考与读数链

用于本流程的相关步骤:准备表面和支承

准备表面和支承

Language note

Titles and introductions are translated; detailed steps, formula explanations and examples remain in Chinese.

Quality gates and return paths

Related instruments, methods and research

Paper links indicate related methods or objects; they do not establish use of this instrument model.

Your next research question. Let’s explore.

Tell us about your material, specimen and measurement goal.

Discuss your application ↗
Find your instrument
⌕
Search products, cases, solutions, standards and literature.