MICROCRE · RESEARCH SCIENCE
Покрытия, тонкие слои и градиентные границы
Перевод ожидает проверки.
Цель исследования
Объедините толщину, границы, поры и локальные свойства, оценивая влияние подложки и шероховатости.
Научные вопросы
层厚变化与局部功能或压入响应的差异是否对应?
界面脱开是原始缺陷还是切割、镶嵌和抛光造成?
所选测试尺度能否分离涂层与基体贡献?
Связь структуры и свойств
硬软相组合容易产生浮雕、涂抹与拉出,因此制样质量直接影响结构解释。
薄层接触响应同时受基体、粗糙度及接触面积模型影响。
截面形貌、局部硬度与附着、耐久或光学功能是不同证据,需要直接功能验证。
Ограничения
层厚十分之一等经验条件不能替代实际基体影响验证。
界面图像良好不等同附着强度或耐久性能合格。
Связанные приборы, методы и исследования
Металлографическая резка →Микротвердомеры →Металлографические микроскопы →Прессы для запрессовки →Шлифование и полирование →Призменные анализаторы →Толщиномеры →
Функциональные покрытия: слои и баланс свойств →Полупроводниковые плёнки: толщина, однородность и перенос →Толщина покрытия: неразрушающий и шлифовой контроль →Шероховатость: направление, фильтрация и функция →Стойкость к среде: воздействие и парные сравнения →Твёрдость и вдавливание: шкала и модель контакта →Оптические свойства: пропускание, преломление и рассеяние →
Металлографическая резка →Микротвердомеры →Металлографические микроскопы →Прессы для запрессовки →Шлифование и полирование →Призменные анализаторы →Толщиномеры →
Связь со статьёй означает общность метода или объекта, а не применение данной модели прибора.
Orientation imaging: The emergence of a new microscopy →The impact of magnesium content on lithium-magnesium alloy electrode performance with argyrodite solid electrolyte →Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques →Scaling approach to conical indentation in elastic-plastic solids with work hardening →Novel high temperature vacuum nanoindentation system with active surface referencing and non-contact heating for measurements up to 800 °C →Using nanoindentation to study the aging of cellulose acetate in cinematographic films →Computational modeling of the forward and reverse problems in instrumented sharp indentation →A procedure for extracting primary and secondary creep parameters from nanoindentation data →Size-affected single-slip behavior of pure nickel microcrystals →A method for interpreting the data from depth-sensing indentation instruments →High temperature nanoindentation – the importance of isothermal contact →Temperature dependence of the indentation size effect →A novel approach for extending autocollimator calibration from plane to spatial angles →Size dependence of mechanical properties of gold at the micron scale in the absence of strain gradients →Infrared Optical Properties of Materials →Anisotropy oxidation behavior and mechanism of textured Ti3(SiAl)C2 ceramic →Establishing isothermal contact at a known temperature under thermal equilibrium in elevated temperature instrumented indentation testing →Evaluation of measurement data — Guide to the expression of uncertainty in measurement →Evaluation of measurement data — Guide to the expression of uncertainty in measurement. Amendment 1: Nonlinearity in measurement models →Evaluation of measurement data — Supplement 1 to the GUM — Propagation of distributions using a Monte Carlo method →Guide to the expression of uncertainty in measurement — Part 6: Developing and using measurement models →Transmission EBSD from 10 nm domains in a scanning electron microscope →Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results →Indentation size effects in crystalline materials: A law for strain gradient plasticity →An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments →On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation →Traceability Calibration, & Measurement Uncertainty Issues Regarding Coordinate Measuring Machines and Other Complex Instruments →Discrepancies between roughness measurements obtained with phase-shifting and white-light interferometry →Fiji: an open-source platform for biological-image analysis →NIH Image to ImageJ: 25 years of image analysis →Quantitative insight into dislocation nucleation from high-temperature nanoindentation experiments →Nanoindentation and contact-mode imaging at high temperatures →Surface characterization of an ultra-soft contact lens material using an atomic force microscopy nanoindentation method →Comparison of Bulk and Micro Sampling Techniques for the Elemental Analysis of SRM 610 and 612 →Deformation mechanism and mechanical properties of TiN/ZrN nanolaminates by nanoindentation: effect of layer thickness and temperature →High-Temperature Mechanical Characterization of CeO2 as a Ceramic Surrogate Fuel Based on FIB and Nanoindentation →Thermally Activated Deformation Mechanisms in MgO Investigated via High Temperature Scanning Indentation →AFM z-piezo calibration method for height measurements in the sub-nanometer to nanometer range using stepped surfaces →Hot nanoindentation in inert environments →Sample dimensions influence strength and crystal plasticity →Certification of Standard Reference Material® 2246a Relative Intensity Correction Standard for Raman Spectroscopy: 830 nm Excitation →NIST Surface Roughness and Step Height Calibrations: Measurement Conditions and Sources of Uncertainty →Mechanical Metallurgy on Columbia Gas X100 Experimental Pipe →Elevated temperature, in situ indentation with calibrated contact temperatures →High-resolution elastic strain measurement from electron backscatter diffraction patterns: new levels of sensitivity →A systematic study of sample preparation-induced martensitic phase formation in 304 L austenitic stainless steel →EURAMET Calibration Guide — 硬度计校准与不确定度评定 →NPL Good Practice Guide — 不确定度预算的编制 →Evaluation of measurement data — Guide to the expression of uncertainty in measurement (GUM) →
